This is the Great Planes ElectroStik EP Sport Electric ARF Airplane.
It's an entirely new take on the classic "Stik" design that has been a favorite among R/C pilots for years! All flight surfaces are prehinged with control horns mounted to shorten assembly time and ensure perfect alignment. Flight-ready after just one hour of simple assembly with no gluing! Rx-R version comes with a quality ElectriFly brushless power system and three ES80 micro servos just add a receiver and battery. Available as a Rx-R or an ARF!
A Rx-R is more than an ARF it's a new level of pilot ease! The on-board gear below is included and installed. Add a receiver and battery and you're ready to fly!
ElectriFly RimFire 42-40-1000 Out-runner Brushless Motor. An extremely high power-to-weight ratio makes this the ideal choice for the ElectroStik. Tightly wrapped windings push efficiency up to 77%. ElectriFly SS45 Brushless ESC hooks up in seconds, and delivers superbly smooth, precise response throughout the throttle range. Comes with Dean's connectors.
ElectriFly ES80 Micro Servo delivers exceptional torque and speed, and weighs only 0.6 ounces.
The main wing slides onto this lightweight carbon fiber tube and bolts together with just four screws and two straps no messy epoxy!
The horizontal and vertical stabilizers simply bolt together, without measuring or gluing.
The included servos are quality ElectriFly ES80 micro servos, already installed so that all you have to do is plug in your receiver.
RimFire 42-40-1000 out-runner brushless motor. The recommended RimFire 42-40-1000 out-runner brushless motor delivers plentiful, dependable power.
Access to the roomy interior is quick and easy, allowing for convenient battery changes. The wing attaches quickly with these two EZ Bolt thumb screws no tools required!
With its 52.75" wingspan, the ElectroStik is ideally sized for both excellent performance and transportation ease.
With its low number of parts and high amount of prefabrication, your ElectroStik requires only an hour of final assembly.
One Great Planes ElectroStik EP ARF with landing gear, wing joiner tube, three foam wheels, spinner, hardware and instruction manual
6" (152mm) Extension: For aileron servo
Motor: Rimfire brushless outrunner 42-40-1000kV GPMG4675 or
ESC for Brushless Motors: GPMM1840
Battery: LiPo 3200mAh 11.1V 20C Discharge w/Balance connector
Cell Balancer: GPMM3160
Battery Charger: LiPo compatible
- Construction: Balsa and ply with prehinged flight surfaces and preinstalled control horns
- Wings: Two piece with carbon fiber wing joiner
- Covering: Top Flite MonoKote
- Aileron Control: Single servo, servo trays in wings for optional dual servo control
- Landing Gear: Prebent and painted aluminum
- Wheels: Main-two foam 2.25" (57mm) diameter, tailwheel .75" (19mm) diameter
- Spinner: Constructed of plastic, red in color, 2.25" (57mm) diameter
- Hardware: Full set included
- Building Time: Approximately two hours
- Warranty: Great Planes Model Manufacturing Company guarantees this kit free from defects in both materials and workmanship at date of purchase.
Wingspan: 52.75" (1340mm)
Wing Area: 589 sq in (38 sq dm)
Weight: 3 - 3.5lb (1360 - 1587g)
Airfoil: Semi symmetrical
Wing Loading: 11.7 - 13.6oz/sq ft (36 - 42g/sq dm)
Length: 45.5" (1155mm)
Center of Gravity: 3-5/8" (92mm) back from leading edge of wing at fuselage
Elevator up & down: 1/8" (3.2mm) 5 degrees
Rudder right & left: 5/8" (15.9mm) 25 degrees
Ailerons up & down: 3/8" (9.5mm) 15 degrees
Elevator up & down: 1/4" (6.4mm) 10 degrees
Rudder right & left: 1-1/8" (28.6mm) 50 degrees
Ailerons up & down: 1/2" (12.7mm) 20 degrees