My Cart:
0 item(s)
Total: 0.00 

Hot Categories

Find Parts by Vehicle

Search Refinement

  Home > RC Car & Truck Parts >

  RPM Axle Carriers Oversized Bearings Black Revo RPM80582

RPM80582 RPM Axle Carriers & Oversized Bearings Black Revo

List Price: $34.95
Our Price: $27.89
Save $7.06!

Stock Status:

 In Stock

Product Code: RPM80582

Technical Specs

RPM axle carriers for the Traxxas Revo, T-Maxx 3.3 have been painstakingly redesigned to improve the durability, strength, and reliability of these much-abused parts. Check out this laundry list of features built into each set of RPM Revo carriers:

Axle Carriers:

Stock replacement ?no modifications are needed to bolt them in.

Larger bearing bores accept RPM oversized bearings.

Included in each kit are two 15mm bearings and two 21mm bearings.

The wall thickness around the pillow-balls has been increased by 40% - eliminating split walls!

More than 20% more material supports the pillow-balls, preventing them from pulling through.

Redesigned reinforcing rib supporting the tie rod mount.

Redesigned boot lock tabs making removal of the silicone boots easier.

Press-fit bearings in the carrier means reduced movement of the axle in the carrier.

Oversized Bearings:

Outer bearings are 6x15x5mm (stock is 6x12x4mm).

Inner bearings are 12x21x5mm (stock is 12x18x4mm).

Wider bearings create an additional 2mm of contact with the axle for smoother, longer running performance.

3mm. larger bearings have balls a full 33% larger than stock!

The load ratings of RPM oversized bearings are double that of stock bearings and more than triple the fatigue rating of stock bearings as well!

Pillow-Ball Setscrews:

Two-piece design uses aluminum and Delrin for the ultimate in holding power under extreme situations.

Our aluminum setscrews reduce movement of the pillow-balls in the carrier.

Our Delrin bushing caps have more than twice the contact area on the pillow-ball, keeping the pillow-balls locked in place at all times.

RPM Revo axle carriers are sold with 1 left and 1 right axle carrier, 2 outer 15mm bearings, 2 inner 21mm bearings, 4 aluminum setscrews, 4 Delrin bushing caps, and detailed instructions to help install them on your truck. Replacement bearing sets (#80570) come with 2 inner 21mm bearings & 2 outer 15mm bearings.

Average Customer Review: 3 of 5 | Total Reviews: 2

Review This Product

  0 of 0 people found the following review helpful:
Poor threading June 18, 2013
Reviewer: Anonymous Person  
Disappointed with the quality of these.  I'm a big RPM fan, but they dropped the ball on these. The plastic is very soft compared to the aluminum retaining nuts for the pillow balls, so much so that it is nearly impossible to get them to thread correctly without cross threading.  If I had to do it all over again, I would just go with traxxas replacements.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
. April 14, 2012
Reviewer: Tim Nicolas from Brisbane, qld Australia  
I also haven't installed them yet

Was this review helpful to you?

Browse for more products in the same category as this item:

RC Car & Truck Parts
RC Car & Truck Parts > Suspension System
Category > Suspension System
Traxxas R/C Parts
Traxxas R/C Parts > Traxxas Revo 3.3 4WD
Shop by Brand > RPM Products
Find Parts by Vehicle
Traxxas R/C Parts > Traxxas E-Maxx
Traxxas R/C Parts > Traxxas T-Maxx 3.3
Traxxas R/C Parts > Traxxas E Maxx Brushless
Traxxas R/C Parts > Traxxas E-Revo 1:10
Traxxas R/C Parts > Traxxas E-Revo 1:16 Brushless
Traxxas R/C Parts > Traxxas T-Maxx 2.5