E-Flite Power 10 Outrunner Motor Brushless 1100Kv EFLM4010A

E-Flite Power 10 Outrunner Motor Brushless 1100Kv EFLM4010A
Back Order Now
You may back order this item and it will ship when it arrives.
$3.99 flat rate shipping! Learn More
Price: $68.99

Please Log in to receive a notification when this item arrives in stock.

Save In List
This item earns up to 69 VIP Reward Points Learn More

This is the E-Flite Power 10 Brushless Outrunner Motor 1100Kv.


  • Equivalent to a 10-size glow engine for 32–48 ounce (910–1360 g) airplanes
  • Ideal for 3D airplanes weighing 28–36 ounces (790–1020 g)
  • Ideal for models requiring up to 450 watts of power
  • High-torque, direct-drive alternative to inrunner brushless motors
  • Includes mount, prop adapters and mounting hardware
  • External rotor design—5mm shaft can easily be reversed for alternative motor installations
  • Slotted 14-pole outrunner design
  • High-quality construction with ball bearings and hardened steel shaft
  • Quiet, lightweight operation

You Will Need:

  • 40A ESC
  • 6- to 10-cell Ni-MH/Ni-Cd or 2–3S Li-Po
  • 10x5 to 12x6 electric props


Type: Brushless outrunner motor
Size: 10-size
Bearings or Bushings: One 5 x 14 x 5mm Bearing, and One 5 x 11 x 5mm Bearing
Wire Gauge: 16
Recommended Prop Range: 10x5—12x6
Voltage: 7.2—12
RPM/Volt (Kv): 1100
Resistance (Ri): .043 ohms
Idle Current (Io): 2.10A @10V
Continuous Current: 32A
Maximum Burst Current: 42A (15 sec)
Cells: 6—10 Ni-MH/Ni-Cd or 2—3S Li-Po
Speed Control: 35—40A brushless
Weight: 122 g (4.3 oz)
Overall Diameter: 35mm (1.40 in)
Shaft Diameter: 5mm (.20 in)
Overall Length: 43mm (1.60 in)

Tech Notes:
Maximum Operating Temperature: 220 degrees Fahrenheit
Adequate cooling is required for all motor operation at maximum current levels.
Maximum Burst Current duration is 15 seconds.
Adequate time between maximum burst intervals is required for proper cooling and to avoid overheating the motor.
Maximum Burst Current rating is for 3D and limited motor run flights.
Lack of proper throttle management may result in damage to the motor since excessive use of burst current may overheat the motor.

NOTE: All data measured at full throttle. Actual performance may vary depending on battery and flight conditions.

E-flite Brio 10
Motor: Power 10
ESC: E-flite 40A Brushless V2 (EFLA311B)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power PRO LITE 2100mAh 11.1V 3-Cell (THP21003SPL)
Flying Weight w/Battery: 2.1 lbs
Amps: 37.2
Volts: 9.6
Watts: 357
Input Watts/Pound: 170
RPM: 7800

  • Expect good speed and extreme vertical power for artistic aerobatics. Average duration is approximately 6-9 minutes depending on throttle management.

E-flite Ultimate 20-300 10e
Motor: Power 10
ESC: E-flite 40A Lite Pro SB Brushless (EFLA1040L)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power 2600mAh 11.1V 3S PRO LITE V2 Li-Po (THP26003SPL2)
Flying Weight w/Battery: 40.7 oz (2.5)
Amps: 40.2
Volts: 10.7
Watts: 430
Input Watts/Pound: 172
RPM: 8350

  • Expect ballistic power very strong vertical performance ideal for pulling out of hovers. Average duration is approximately 5-8 minutes depending on throttle management.

This product was added to our catalog on December 5, 2007