Hobbywing XRotor Micro 4in1 ESC with Flight Controller Combo HWI38040300

Hobbywing

https://www.rcplanet.com/hobbywing-xrotor-micro-4in1-esc-with-flight-controller-combo-hwi38040300/
$137.00 $99.99
(You save $37.01)
Status: In Stock
(No reviews yet)
UPC:
088718500333
Availability:
<span style="color: #D70200;"><strong>Unavailable</strong></span><br /><span style="color: #D70200;"><strong>Sandy, Utah</strong></span>

Item # HWI38040300

More information about Hobbywing XRotor Micro 4in1 ESC with Flight Controller Combo HWI38040300

This is a HobbyWing XRotor Micro 4-in-1 BL32 ESC with an F4 G2 Flight Controller.

Specs:
Cont. Current: 45a
Peak Current: 60A
BEC: 5V@1.5A/10V@1.5A
Lipo: 3-6S LiPo
Weight: 11.5g
Size: 32.7x18.4x6.2mm
Firmware Version: OMNIBUSF4SD
Size: 36x36mm

  • High performance 32-bit microprocessor with the running frequency of up to 48MHz for excellent performance
  • BLHeli_32 firmware is the third generation BLHeli, following base BLHeli and BLHeli-S
  • All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling
  • The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work
  • The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us)
  • Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up
  • STM32 F405 MCU allows the FC to run the PID looptime and gyro with higher frequency
  • The SPI ICM-20602 which integrates accelerometer and gyro (with the running frequency can be set to 32KHz) is adopted
  • Onboard OSD microchip which supports the DMA mode allows users to adjust its parameters via the Betaflight software. (Note: the OSD is controlled by the F4 MCU.)
  • The FC which supports Betaflight firmware & allows parameter adjustment via Betaflight software is more applicable to FPV race
  • TF-card which can record and save more flight/black box data allows users to adjust the setup of their aircraft easily
  • Compatible with various receivers like SBUS, SUMH, SUMD, SPEKTRUM1024/2048, XBUS, PPM and etc
  • LED strip signal output port allows users to adjust the color & flash mode of the LED strip via the FC
  • Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port , extra current meter is needed)
  • Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft
  • Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters
You Might Also Like...

You Might Also Like...

Overview

More information about Hobbywing XRotor Micro 4in1 ESC with Flight Controller Combo HWI38040300

This is a HobbyWing XRotor Micro 4-in-1 BL32 ESC with an F4 G2 Flight Controller.

Specs:
Cont. Current: 45a
Peak Current: 60A
BEC: 5V@1.5A/10V@1.5A
Lipo: 3-6S LiPo
Weight: 11.5g
Size: 32.7x18.4x6.2mm
Firmware Version: OMNIBUSF4SD
Size: 36x36mm

  • High performance 32-bit microprocessor with the running frequency of up to 48MHz for excellent performance
  • BLHeli_32 firmware is the third generation BLHeli, following base BLHeli and BLHeli-S
  • All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling
  • The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work
  • The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us)
  • Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up
  • STM32 F405 MCU allows the FC to run the PID looptime and gyro with higher frequency
  • The SPI ICM-20602 which integrates accelerometer and gyro (with the running frequency can be set to 32KHz) is adopted
  • Onboard OSD microchip which supports the DMA mode allows users to adjust its parameters via the Betaflight software. (Note: the OSD is controlled by the F4 MCU.)
  • The FC which supports Betaflight firmware & allows parameter adjustment via Betaflight software is more applicable to FPV race
  • TF-card which can record and save more flight/black box data allows users to adjust the setup of their aircraft easily
  • Compatible with various receivers like SBUS, SUMH, SUMD, SPEKTRUM1024/2048, XBUS, PPM and etc
  • LED strip signal output port allows users to adjust the color & flash mode of the LED strip via the FC
  • Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port , extra current meter is needed)
  • Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft
  • Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters

Product Questions