Great Planes ElectriFly Silver Series 60A Brushless ESC Hi Volt GPMM1850

Great Planes

Item # GPMM1850
$149.99 $99.99
(You save $50.00)
Status: In Stock
UPC:
735557418502
Great Planes ElectriFly Silver Series 60A Brushless ESC Hi Volt GPMM1850

More information about Great Planes ElectriFly Silver Series 60A Brushless ESC Hi Volt GPMM1850

This is the ElectriFly Silver Series 60amp Hi volt brushless electronic speed control. Capable of handling up to 50V on the input and 60 amps of continuous current on the output, the SS-60 is designed for larger high-performance electric airplanes.

Includes:

  • ElectriFly Silver Series 60A Hi Volt Brushless Electronic Speed Control
  • 4 (10cm) 14AWG silicone insulated battery wires
  • 6 (15cm) 14AWG silicone insulated motor wires
  • pre-installed universal radio connector
  • Deans Ultra battery connector
  • 4mm female bullet motor connectors


Requires: Mating motor and battery connector

Note:
The Silver Series line of brushless electronic speed controls include many built-in safety features. One such feature could possibly cause the brushless motor to stop rotating when the transmitter's stick is at an extremely low position and/or if rotation of the brushless motor is impeded or obstructed in some way. This is normal, as the ESC is detecting that a problem possibly exists with the motor and/or speed control. Rotation of the motor is stopped to protect the speed control from possible damage.

Warning: If the ESC and motor have already been armed and the motor has been rotating normally, yet after moving the throttle stick to near minimum the motor suddenly ceases to rotate normally even if the throttle stick is advanced above minimum throttle, do not place your hands near the propeller! Failure to obey this warning could result in personal injury. From this point, moving the throttle stick up - even to full throttle might not cause the motor to rotate but the motor is still armed and active during this time. To regain control of the motor, move the throttle stick to absolute minimum throttle position and then advance the throttle stick upwards once again. Alternatively, you can disconnect the battery from the ESC, then re-connect the power source and re-arm the system. Never get near the propeller if the speed control is connected to input power! Always make sure the throttle stick is at minimum position before attempting to disconnect the battery from the speed control! ElectriFly is not responsible for incidental damage or personal injury as a result of misuse of this product.

  • Compatible with NiCd, NiMH and LiPo batteries, handles 14-32 NiCd/NiMH cells or 4-12 LiPo cells (12.4-50V)
  • Handles up to 50V on input and the pulse-width modulated output delivers 60A continuous current and 72A surge current
  • Very little programming required for ease of use and no-hassle flying fun, an optional Programming Card allows adjustment of brake (ON or OFF), motor rotation (forward or reverse), timing angle (12 or 20º), operating frequency (8kHz or 16kHz), or custom setting of low battery cutoff voltage (12.4-37.0V)
  • Safe-Start function prevents accidental propeller rotation
  • Opto-isolated radio control (no BEC) for smooth, precise, trouble-free RF signals
  • 8.5kHz operating frequency for smooth throttle response, good run-time and cool operation
  • Audible setup tones
  • Fully proportional forward with ON/OFF brake
  • Mounting tabs for easy mounting and good airflow for cooling

Input Voltage: 14-32 NiCd/MH cells, 4-12 LiPo cells (12.4-50V)

BEC: No BEC circuit, opto-isolated

Output Current: 60A continuous max., 72A surge max.

Max. Output Power: 3000 watts

ON-Resistance: 0.004 ohms

Thermal Cutoff: 230ºF (110ºC)

Dimensions: 2.3 x 1.9 x 0.7 in. (58 x 48 x 18mm)

Weight: 3.13oz. (89g, w/Deans Ultra plug, Rx plug, three 4mm bullets)

Manual Setup

Brake: ON or OFF

Rotation direction: forward only

Timing angle: 12º only

Operating frequency: 8kHz only

Low voltage cutoff: Starting battery voltage x 0.74

Setting w/Optional Programming Card

Brake: ON or OFF

Rotation direction: forward or reverse

Timing angle: 12 or 20º

Operating frequency: 8kHz or 16kHz

Low voltage cutoff: 12.4 - 37.0V adjustable