Tekno RC NB48.4 1/8 4WD Competition Nitro Buggy Kit TKR8300

(You save $370.00 )
Sold Out
Related Products:
Sold Out
Add to Cart
(You save $370.00 )

Sold Out


Build Type, Power Type, Scale, Skill Level, Vehicle Type, Free Shipping, Color/Graphics,


Build Type:
Unassembled Kit
Power Type:
Nitro Power
Skill Level:
Skill Level 5
Vehicle Type:
Free Shipping:
This item qualifies for free shipping! Click Here!
Color and/or graphics may differ from image shown.


View All



View All



This is the 1/8 scale glow Powered, radio controlled, 4WD Competition NB48.4 buggy kit from Tekno RC.


  • NB48.4 Buggy Kit
  • Shock and Diff Oil
  • Threadlock
  • clear Body
  • 13T Clutch Bell
  • 48T Spur Gear
  • High-Downforce Wing
  • Decals
  • Shock and Diff Oil
  • Instructions


  • 2-3ch radio with high-torque/speed steering & throttle servos
  • .21 cu in (3.4cc) glow engine with tuned pipe
  • Hump receiver battery
  • 1/8 scale buggy tires and wheels
  • Starter box & glow igniter
  • Polycarbonate safe spray or brush on paint
  • Building and track equipment

Note: Engine shown in photo is not included.


  • Chassis: CNC machined hard anodized lightened 7075 aluminum, 0.16" (4mm) thick, short overhang for better bump handling and jump landing, adjustable brace system
  • Drive: Four wheel with CV driveshafts and captured pins on wheels
  • Clutch: Adjustable, four 7075 aluminum shoes
  • Clutch Bell: 13T CNC machined steel, CNC machined flywheel
  • Fuel Tank: 4.2oz (125cc), IFMAR legal integrated filter/clunk with external nipple
  • Differentials: Three fluid filled adjustable lightweight diffs
  • Suspension: Fully adjustable long travel, adjustable front arm sweep and angle, front and rear sway bars, captured outer front and rear hinge pins, adjustable hinge pin braces, narrow high roll, center rear hubs, new bearing supported spindle/carrier with updated geometry and enhanced durability
  • Steering: Ball bearing equipped, narrow pivot steering posts, adjustable steering stops for precise travel setting, new bellcranks, with optional solid right bellcrank (no servo saver) for increased steering response
  • Shocks: 16mm bore CNC machined hard anodized threaded aluminum bodies, 4mm hardened steel polished shock shafts, CNC machine tapered pistons, CNC aluminum shock caps, preload adjusters and cartridge caps, Triple Guide Design for reduced shaft deflection, new clamping spring perches w/captured shock boots, options for vented cap, emulsion, or standard shock configurations
  • Front Shock Tower: 0.24" (6mm) CNC machined 7075 aluminum
  • Rear Shock Tower: 0.20" (5mm) CNC machined 7075 aluminum
  • Engine Mount: Adjustable
  • Brakes: CNC machined steel disc with semi-metallic pads
  • Wing: New high downforce Wing, adjustable LCG lightweight mount
  • Radio Tray: Integrated with right mud guard allowing receiver & battery to sit on chassis for lowest CG possible
  • Throttle Control: CNC machined assembly riding on ball bearings
  • Spur Gear: 48T steel
  • Ackerman: Adjustable, Ackerman describes the effect of the inside front wheel turning faster than the outside front wheel during turns, CNC aluminum Ackerman plate rides on precision ball bearings
  • Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis
  • Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle


Length: 17.1" (435mm) without wing
Width: 12-12.2" (306-310mm)
Wheelbase: 12.7-13.2" (323-335mm) adjustable
Dry Weight: 7.17lb (3260g), varies depending on equipment
Diff Ratio: F/R-12/39t, center-48t
RX Battery Box Dimensions: 2.3 x 1.4 x 1.3" (58.5 x 36 x 34.5mm)

Length: 13.4" (340mm)
Width: 7.2" (183mm)
Height: 4" (102mm)

You Might Also Like...